Electrician in Frederickson

The Census Bureau counts about 8,500 homes in Frederickson. Rounded, here is what that looks like:

• About 59% were built in 2000 or later.
• About 17% were built in the 1990s, and 10% in the 1980s.
• About 14% were built before 1980.
• About 74% are single family homes, 10% are attached homes like townhomes, 9% are manufactured or mobile homes, and about 6% are in buildings with three or more units.
• About three quarters of households own their homes.

Source: U.S. Census Bureau, 2020 to 2024 American Community Survey 5-year estimates for Frederickson, via Census Reporter.

That makes Frederickson one of the newer neighborhoods around. Newer wiring is a good start, but a lot of these homes were built before anyone was plugging in a car or running a heat pump, and a panel that was fine on day one can fill up fast.

Nobody tracks electrical problems by neighborhood. This list comes from the age and type of homes above, and from problems that are well known in homes of each era.

A panel that's full

Newer homes often come with 200 amp service. That sounds like plenty until you add an EV charger, a heat pump, a hot tub and a workshop. Signs of trouble are no open breaker slots, tripping breakers, and lights that dim when a big appliance kicks on. An electric panel upgrade or a subpanel gives you room.

EV charging without a plan

A Level 2 charger needs its own dedicated 240-volt circuit, and the panel has to be able to carry the load. We check before we quote. See EV charger circuit installation and Level 2 charging stations.

Surges and storm outages

With more electronics in newer homes, a surge costs more than it used to. A whole house surge protector guards your TV, fridge and computers, and a generator keeps the power on when a windstorm takes the lines down.

Manufactured homes

About 750 homes in Frederickson are manufactured or mobile homes. They have their own wiring and grounding setups, and they need an electrician who looks closely before changing anything. We start with an electrical inspection and go from there.

The older homes mixed in

About 1,200 Frederickson homes were built before 1980. Those can have aluminum branch wiring, two-prong outlets and older panels, like homes anywhere else. We can look at wiring repair and outlet repair.

Garage, shop and outdoor power

Many newer homes have a garage that's become a workshop or a gym. More tools and a bigger load mean more outlets, a subpanel and better lighting. See outlet installation and outdoor lighting.

When a newer home needs more power, the upgrade is mostly about adding capacity for what you plan to run. Here is how a job goes.

1. Free estimate. We look at your panel, add up what you run now and what you plan to add, like a charger or heat pump, and tell you what it takes. You get a price before work starts.
2. Permit. We pull the electrical permit so the work gets inspected.
3. Plan the shutoff. We tell you how long the power will be off before we start.
4. The swap or the add. We install the new panel or the subpanel, connect the grounding, and label each circuit.
5. Inspection and walkthrough. After it passes, we show you the new setup and where the main shutoff is.

See panel replacement and circuit breaker replacement for smaller jobs.

A newer home is full of things that stop working when the power goes out: the garage door, the sump pump, the fridge, the router. A generator keeps them going. Here is how it goes.

1. Free estimate and sizing. We help you decide between a whole home generator and a standby generator that covers the circuits that matter most.
2. Permits. We pull the permits and coordinate with Puget Sound Energy so the install passes inspection.
3. Install day. We set the pad, run the gas or propane line, install the transfer switch, and connect it to your panel.
4. Test. We run the whole system start to finish before we leave.
5. Upkeep. Our generator maintenance and generator repair keep it ready.

EV chargers are one of our most common jobs in newer neighborhoods. Here is how an EV charging station installation goes.

1. Free estimate and panel check. We check how much room your panel has and tell you if it can take a charger as is.
2. Pick the spot. Garage wall, side of the house, or near the driveway. We plan the route for the wire.
3. Permit. We pull the required electrical permit.
4. Install. We run a dedicated 240-volt circuit and mount the charger. We install Tesla chargers and other residential EV chargers.
5. Test. We test it with your car and show you how it works.

Frederickson is unincorporated Pierce County, and electrical work here needs a permit. Tacoma Power handles permits and inspections for the properties it serves in unincorporated Pierce County, and L&I handles the rest. We check which one applies to your address, pull the permit, and schedule the inspection.

Frederickson is a census-designated place in Pierce County. It covers about 11 square miles and sits between Puyallup, Spanaway and Parkland. Public schools are part of the Bethel School District.

The area is also home to the Frederickson Manufacturing/Industrial Center, a large industrial zone with employers like Boeing. The homes are mostly on the residential side of that, in neighborhoods that were built up over the last twenty years.

We work all over this part of Pierce County. If you're in South Hill, Puyallup or Clover Creek, we've got a page for you. See all of our areas served, including Tacoma, Lakewood, University Place, Federal Way, Bonney Lake, Auburn and Fife.